Three Loads, One Question: Does It Actually Hold?
Mechanical Strength Testing across tensile, flexural, and compression loading at our Oragadam laboratory — run on 5–300 kN universal testing machines for medical device, industrial, and automotive testing programmes.
Call 90876 86986 WhatsApp UsA component can pass a pull test and still fail the moment it’s bent, or pass a bend test and still crumble the moment it’s actually loaded straight down.
Mechanical Strength Testing is the umbrella that covers all three of a material’s core load responses in one accredited scope, because no single test tells the full story on its own. Our capability at the Oragadam laboratory spans a range of universal testing machines from 5 kN up to 300 kN Servotec capacity, letting a single lab handle everything from a delicate polymer film to a full-scale structural bracket under one roof. Tensile Testing for plastics pulls a specimen to failure along a single axis, capturing strength, elongation, and modulus — the baseline mechanical fingerprint every material data sheet is built around.
Flexural testing loads a specimen across a supported span instead, putting the outer and inner fibres in opposite stress states at once, which is exactly the loading pattern a housing wall, a rib, or a structural panel actually experiences in service. Compression testing pushes the opposite direction entirely, applying axial load until the specimen crushes, buckles, or deforms, a failure mode tensile and flexural data alone can’t predict. Running all three loading types under one accredited programme means a design team gets a complete mechanical picture from a single sample submission instead of chasing three separate vendors for three separate reports.
The same 5–300 kN machine range that supports our medical device work is exactly what automotive testing programmes need too — interior trim, connector housings, and structural composite panels are qualified against the same tensile, flexural, and compression fundamentals, just referenced to different industry standards. That shared equipment base is why manufacturers moving between medical device work and other industrial programmes find it faster to qualify a material once at Kiyo R&D Lab rather than re-establishing a new lab relationship for every new vertical. Manufacturers bring their programmes to Kiyo R&D Lab because a single missed mechanical checkpoint doesn’t surface as a data-sheet footnote — it surfaces as a cracked housing, a buckled bracket, or a component that fails the very first time it’s actually loaded the way it was designed to be. Running the full mechanical panel under one accredited scope at Oragadam, with reports formatted for direct regulatory submission, is what turns three separate load curves into evidence your quality team can actually stand behind.
Three Load Types, One Mechanical Strength Testing Programme
Run on 5–300 kN universal testing machines at Oragadam
Tensile Testing
Pull-to-failure strength, elongation, and modulus on 5–300 kN UTMs
ASTM D638 / ISO 527
Flexural Testing
Three-point bend strength and modulus across the same UTM range
ASTM D790 / ISO 178
Compression Testing
Compressive strength and modulus under axial load to failure
ASTM D695 / ISO 604
How Our Mechanical Testing Process Works
Four steps, from sample intake to a validated report
Machine Selection
Sample matched to the right capacity UTM — 5 kN, 30 kN, or 300 kN.
Specimen Preparation
Cut and conditioned to the applicable ASTM / ISO geometry.
Load to Failure
Full curve captured across tensile, flexural, or compression loading.
Certified Report
Delivered digitally, ready for your validation file.
Standards Behind This Programme
| LOAD TYPE | SCOPE | STANDARD |
|---|---|---|
| Tensile Testing for plastics | Single-axis pull to failure | ASTM D638 / ISO 527 |
| Flexural testing | Three-point bend across supported span | ASTM D790 / ISO 178 |
| Compression testing | Axial load to crush or buckle | ASTM D695 / ISO 604 |
Kiyo R&D Lab – Oragadam
Our Mechanical Strength Testing floor, spanning medical device and industrial programmes, is based at No.13, Srinivasa Perumal Street, Panapakkam, Serapanacheri, Greater Chennai, Tamil Nadu 601301.
Frequently Asked Questions
What does Mechanical Strength Testing cover? +
It covers all three core load types, run on 5–300 kN universal testing machines and referenced to ASTM D638/D790/D695 and ISO 527/178/604.
Why does Tensile Testing for plastics alone not tell the full mechanical story? +
A material can pass one load type and still fail another, since tensile, flexural, and compression loading each stress the material’s internal structure differently, so a complete mechanical picture needs all three rather than assuming one predicts the others.
Do you support automotive testing alongside medical device work? +
Yes. Our 5–300 kN UTM range and tensile, flexural, and compression methods are the same fundamentals automotive testing programmes rely on for trim, connector housings, and structural composite panels, just referenced against different industry-specific standards on request.
Can I run all three load types on the same specimen batch? +
Yes, provided enough specimens are moulded or cut from the same material lot; our team confirms the exact specimen count once your material, geometry, and required load types are known.
How do I get a quote for this testing? +
Call us at 90876 86986, message us on WhatsApp, or fill in the enquiry form below with your material and testing needs.
Book Your Mechanical Testing Today
Talk to our Oragadam team about your next material qualification — for medical device, industrial, or automotive programmes alike.
Call 90876 86986 WhatsApp UsRequest Mechanical Strength Testing
Fill in your details below and our team will get back to you shortly.